kit:parts_list_v007
Differences
This shows you the differences between two versions of the page.
Both sides previous revisionPrevious revisionNext revision | Previous revision | ||
kit:parts_list_v007 [2016/12/26 13:43] – Formatting steve | kit:parts_list_v007 [2018/08/01 13:37] (current) – external edit 127.0.0.1 | ||
---|---|---|---|
Line 12: | Line 12: | ||
*SD Card shield Cost: $2.00 | *SD Card shield Cost: $2.00 | ||
- | Current total cost: $28.00 | + | Current total cost: $28.00 |
==== Raspberry Pi Core ==== | ==== Raspberry Pi Core ==== | ||
- | * Raspberry Pi Zero with camera | + | * Raspberry Pi Zero with camera bundle. Current best price: $40 (Adafruit) |
* Raspberry Pi servo hat. Current best price: $18 (Adafruit) | * Raspberry Pi servo hat. Current best price: $18 (Adafruit) | ||
+ | * Edimax USB wifi dongle. Current best price: $8 (Amazon) | ||
- | Current total cost: $58.00 | + | Current total cost: $66.00 |
+ | ===== Components ===== | ||
+ | * Hookup wire: 22AWG stranded. 25 feet RED, 25 feet BLACK. Cost: $6.00 for both spools | ||
+ | * Dupont jumpers: GET COUNT. GET LENGTH. DETERMINE ENDS. FIND SOURCE. | ||
+ | * 1x Half-size breadboard. Cost: $5.00 | ||
+ | * 3x Two-position screw terminals for breadboard. Cost $Repackaged from bulk | ||
+ | * 3x Mini limit switches for lid. Cost: $2.00 for three | ||
+ | * 4 pairs 22AWG m/f bullet terminals (8 pieces total) Cost: $Repackaged from bulk | ||
+ | * 8ft 24 AWG bare copper wire. Cost: 25 cents per CrowBox if bought in bulk & portioned | ||
+ | * Otherwise, cost for entire roll | ||
+ | |||
+ | Current total cost: $13.25 presently, but not all items accounted for yet. | ||
+ | |||
+ | ===== Voltage Regulator Components ===== | ||
+ | * The actual regulator chip | ||
+ | * LM7806CZ DC 1.5A Positive Voltage Regulator, 6V | ||
+ | * Capacitor #1 | ||
+ | * Capacitor #2 | ||
+ | * Diode | ||
===== Motor ===== | ===== Motor ===== | ||
MG995 Metal gear servo. Current best price: $6.00 per servo | MG995 Metal gear servo. Current best price: $6.00 per servo | ||
Line 27: | Line 46: | ||
====== Structural ====== | ====== Structural ====== | ||
+ | All information in this category currently assumes fabrication at PONOKO.COM | ||
+ | |||
*1/4 inch acrylic rod (for push rod) | *1/4 inch acrylic rod (for push rod) | ||
- | *1/ | + | *790x384x3mm |
- | *1/ | + | *181x181x3mm |
- | *1/ | + | *384x384x3mm |
- | *1/8" acrylic | + | *384x384x.5mm styrene |
+ | |||
+ | Current Cost: $41.36 plus shipping | ||
+ | |||
====== Fasteners ====== | ====== Fasteners ====== | ||
Line 37: | Line 62: | ||
*M3 nuts | *M3 nuts | ||
*Silicone rubber band for lid, two inch (include extras). Current best price: 25 cents per band | *Silicone rubber band for lid, two inch (include extras). Current best price: 25 cents per band | ||
+ | |||
+ | Current Cost: [Not done building the list of required fasteners] | ||
+ | |||
+ | ====== Grand Total ====== | ||
+ | **NOTE:** - This information is just the sum of the categories above. It WILL change before shipping. Some parts are not yet sourced, priced, or best-priced, | ||
+ | |||
+ | ===== Arduino Core ===== | ||
+ | $88.61 | ||
+ | |||
+ | ===== Raspberry Pi Core ===== | ||
+ | $126.61 | ||
kit/parts_list_v007.txt · Last modified: 2018/08/01 13:37 by 127.0.0.1